Thought it might be of interest
| SkyWolverines.com http://skywolverines.com/ |
|
| Interesting video on modern heli rotor blades http://skywolverines.com/viewtopic.php?f=6&t=1928 |
Page 1 of 1 |
| Author: | MadMuz [ Sat Jan 03, 2015 1:35 pm ] |
| Post subject: | Interesting video on modern heli rotor blades |
Thought it might be of interest |
|
| Author: | RayNAiken [ Sat Jan 03, 2015 9:11 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
I didn't know rotor blades moved up and down that much!!!! |
|
| Author: | MadMuz [ Sat Jan 03, 2015 10:17 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
Should see them on a gyro   |
|
| Author: | GyroGeorgia [ Sun Jan 04, 2015 12:19 am ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
Has anyone successfully made and marketed gyro rotor blades with a twist??? A change in the angle/attack along the length? |
|
| Author: | MadMuz [ Sun Jan 04, 2015 12:41 am ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
Yes, Dragon wings, but the twist is the other way for gyros.... we have no pitch in the center and about 6 degrees at the tips.... helicopters have more pitch at the root because they are driven, same for a prop, more pitch near hub and less at the tip   
|
|
| Author: | Arnie M. [ Sun Jan 04, 2015 5:00 am ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
. I love rotor blades !!! its an obsession I think  I would like to see a video of them making those BERP tipped blades from start to finish. Probably some trade secrets involved and they dont want everybody to see it |
|
| Author: | MadMuz [ Sun Jan 04, 2015 1:09 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
I am just interested in how composite gyro rotors are made.... purely out of interest? They worry me (small hand run composites) and I guess knowing how they are made would make them less scary
|
|
| Author: | GyroGeorgia [ Sun Jan 04, 2015 1:17 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
Ya know... there are composite body aircraft out there... And if their batteries would not overheat... they would be fine...
|
|
| Author: | elwood [ Sun Jan 04, 2015 5:10 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
MadMuz wrote: I am just interested in how composite gyro rotors are made.... purely out of interest? They worry me (small hand run composites) and I guess knowing how they are made would make them less scary The secret is Women, Women listen to instructions...... I know your internet data is limited so the rotorblade process starts @ 6:30... https://www.youtube.com/watch?v=_3Ls_aT70cY |
|
| Author: | Arnie M. [ Sun Jan 04, 2015 5:49 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
elwood wrote: MadMuz wrote: I am just interested in how composite gyro rotors are made.... purely out of interest? They worry me (small hand run composites) and I guess knowing how they are made would make them less scary The secret is Women, Women listen to instructions...... I know your internet data is limited so the rotorblade process starts @ 6:30... https://www.youtube.com/watch?v=_3Ls_aT70cY You are right .... give women assembly or manufacturing instructions and they will usually follow them exactly ... we men get thinking too much and always try to "improve stuff" ... or do it "our way" ... improving stuff is OK , but it should be worked out in our design department .... not on the assembly floor. Lots of good stuff in that video .... would be a good introduction for newbies wanting some basic gyro info. . . |
|
| Author: | GyroGeorgia [ Sun Jan 04, 2015 6:30 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
Arnie M. wrote: elwood wrote: MadMuz wrote: I am just interested in how composite gyro rotors are made.... purely out of interest? They worry me (small hand run composites) and I guess knowing how they are made would make them less scary The secret is Women, Women listen to instructions...... I know your internet data is limited so the rotorblade process starts @ 6:30... https://www.youtube.com/watch?v=_3Ls_aT70cY You are right .... give women assembly or manufacturing instructions and they will usually follow them exactly ... we men get thinking too much and always try to "improve stuff" ... or do it "our way" ... improving stuff is OK , but it should be worked out in our design department .... not on the assembly floor. Lots of good stuff in that video .... would be a good introduction for newbies wanting some basic gyro info. . . You feminist you... Next thing you will be telling me... women would do a better job in govt... I can just see it now... Betty POTUS is in the morning briefing in the Oval office... and she hears a Moouslim committed an act of terrorism... and her time of the month starts tomorrow.... Poor terrorist... Hmmm... Maybe this is not such a bad idea... 
|
|
| Author: | Arnie M. [ Sun Jan 04, 2015 8:41 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
'' We need to form a womens batallion ... make sure they are all in their pms mood ... wearing shorts and T-Shirts ... in cammo colors of course ... each holding a wild pig on a leash , going on a stroll thru the desert The Mooo slimss would run back to the caves . |
|
| Author: | MadMuz [ Sun Jan 04, 2015 9:07 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
Imagine if the mooslims do take over women will have to cover up and they will loose their pussy power scary thought
|
|
| Author: | GyroGeorgia [ Mon Jan 05, 2015 12:43 pm ] |
| Post subject: | Re: Interesting video on modern heli rotor blades |
MadMuz wrote: Imagine if the mooslims do take over women will have to cover up and they will loose their pussy power scary thought Ya know... it says a lot about a whole race that cannot control themselves around women... as if they are afraid of what Muz calls pussy power. And we are supposed to respect these folks as equals... just because they have oil to sell... Stupid shit if anyone asked me... but they do not (ask me). |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|